Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Round Rock: What to Know First
CleanRun Duct Repair & Cleaning provides independent Abatement Technologies HVAC cleaning in Round Rock, typically scheduling within 3-5 business days and completing most jobs in a single visit. Every Abatement Technologies system we touch gets a written price before work starts, a camera inspection of every component we clean, and a documented photo record delivered when we leave. We’re not affiliated with Abatement Technologies - we’re an independent service provider who knows their equipment from hands-on work in Round Rock homes, including the Stone Oak Ranch and Teravista neighborhoods where cedar pollen and construction dust stress these systems harder than the manufacturer spec sheet assumes. Call (737) 259-5752 for a free estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 750 Series - evaporator coil fouling from fine limestone dust. The PREDATOR 750’s coil fin spacing is tight enough that Round Rock’s airborne caliche and limestone particulate pack between fins faster than on looser-pitched competitors. We see this in Teravista homes built during the 2018-2021 construction surge. Our fix: remove the coil assembly, apply foaming cleaner formulated for aluminum microchannel fins, then pressure-rinse at a controlled angle so we don’t flatten the fin edge. The camera goes in first. Then we talk.
- HEPA-AIRE SAH Series - blower wheel imbalance from pollen loading. The SAH’s forward-curved blower wheel moves high static, but cedar pollen in Round Rock spring builds unevenly across blade surfaces and throws the wheel out of balance. Vibration follows, then bearing wear. We remove the wheel, clean each blade individually with a soft-bristle rotary tool, and run a static balance check before reassembly. No guesswork on whether the wobble is gone.
- ABATEMENT PAS2400 - condenser coil corrosion at the lower third. The PAS2400’s condenser coil sits low in the cabinet, and Round Rock’s clay-heavy soil splashes alkaline minerals up during hard rains. The lower third corrodes while the top looks fine. We pull the coil, treat the affected section with foaming cleaner and a neutralizing rinse, then document the remaining metal thickness so the homeowner knows if replacement is approaching.
- ABATEMENT BD2K - heat exchanger soot scaling from short cycling. The BD2K’s heat exchanger runs hot when oversized for the duct load, and Round Rock’s tight new construction often pairs it with undersized return plenums. Soot scales on the exchanger walls, dropping efficiency and raising CO risk. We brush-scale the chambers, vacuum with negative-pressure extraction (a contained suction system that keeps debris out of your living space), and pressure-test for cracks before the system restarts.
- ABATEMENT CAP6000 - plenum mold at the evaporator transition. The CAP6000’s evaporator plenum is a single-piece molded design with a flat drainage pad that can hold standing water if the drain pitch is off by even a quarter-inch. In Round Rock’s humid shoulder seasons, that stagnant water breeds mold at the transition to the main trunk. We clean the pad, verify drain pitch with a level, and treat the plenum interior with an EPA-registered sanitizer - but only after photographing the growth pattern so the homeowner sees why the drain fix matters as much as the cleaning.
Our Abatement Technologies HVAC Cleaning Process
- 1
Camera inspection and written scope. We run a borescope through every accessible duct run, plenum, and component chamber. You see what we see on a tablet before we quote a dollar figure. Haven Standard Clause 1: Written Price Before Any Work Starts.
- 2
Component removal and condition assessment. We pull the evaporator coil, blower assembly, or heat exchanger access panel - whatever the job requires - and photograph each component’s condition with a reference scale in frame.
- 3
OEM vs. quality aftermarket decision. For Abatement Technologies parts, we stock direct-fit OEM coils and blower wheels. If an aftermarket equivalent meets the same pressure-drop and efficiency specs (we verify against manufacturer data sheets), we’ll present both options in writing with the price difference stated.
- 4
Cleaning and reassembly. We clean with brand-appropriate chemistry - no caustic foams on aluminum microchannel fins, no high-pressure rinse on aged copper. Each step follows Abatement Technologies’ service manual clearances where they exist, and our own documented protocol where they don’t.
- 5
Performance test and photo record delivery. We measure static pressure before and after, run the system through a full cycle, and deliver your documented photo record via email before the truck leaves. Haven Standard Clause 6: Verified Completion.
- 6
365-Day Done Right Promise activation. The written guarantee goes into your job file. If the work isn’t right, we make it right. No manager approval required - it’s in writing on every job.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Round Rock
Most Abatement Technologies HVAC cleaning jobs in Round Rock fall between $340 and $780 for a complete system service. Single-component cleanings - evaporator coil only, blower only, or condenser only - typically run $180 to $420.
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning | $220 - $420 | Coil accessibility, fin corrosion severity, refrigerant recovery required |
| Blower wheel & housing cleaning | $180 - $340 | Wheel removal difficulty, bearing condition, balance correction needed |
| Condenser coil cleaning | $160 - $300 | Coil depth (single vs. dual row), corrosion treatment, fin combing |
| Full air handler cleaning (coil + blower + plenum) | $480 - $780 | System size, plenum mold treatment, drain line replacement |
| Heat exchanger cleaning & inspection | $280 - $520 | Soot depth, chamber access, CO test protocol |
Factors that push toward the higher end: systems in Round Rock’s 2015-2020 build years with original filters never upgraded from fiberglass, homes within a quarter-mile of active construction (Teravista, Paloma Lake, Forest Creek during expansion phases), and systems that have run without service since installation. We don’t do per-vent pricing or $79 teaser rates. One flat price per system, agreed in writing before work starts. Call (737) 259-5752 for a free estimate - we’ll put our number next to any competitor’s written quote, no charge.
Why Round Rock Homeowners Call CleanRun Air Duct Cleaning Round Rock for Abatement Technologies Work
We’ve cleaned Abatement Technologies equipment in Round Rock since 2013, and we’ve learned what their manuals don’t cover: how cedar pollen loads a SAH blower differently than a Carrier, how PAS2400 condensers fail from the bottom up in clay soil, how the CAP6000’s plenum mold pattern tells you whether the drain is pitched wrong or the pad is cracked. Our technicians are background-checked, uniformed, and identified by name before arrival - Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier systems, so when your home has mixed equipment or you’re weighing replacement brands, we can speak to all of them from direct experience. Every job ends with a documented photo record, not a handshake and a promise. The 365-Day Done Right Promise is in writing, not a policy subject to manager mood.
FAQs
No. Warranty coverage requires that service follow manufacturer specifications, not that the work be performed by Abatement Technologies personnel. We document our cleaning protocol against Abatement Technologies service manual requirements and provide that record with your job file. If a warranty claim arises, you have written evidence that service was performed to spec. For questions about your specific warranty status, call (737) 259-5752 and we’ll review your model and install date.
You receive a documented photo record of every component we accessed - before and after, with timestamps. If we say we cleaned the evaporator coil, you’ll see the coil. If we say we treated the plenum, you’ll see the plenum. This has been standard on every CleanRun job since 2013. No photo, no proof, no invoice.
The $79-$149 range typically covers a shop-vac at the register and a spray of deodorizer. That doesn’t touch the evaporator coil, the blower wheel, or the plenum - the components that actually affect your air quality and system efficiency. Our price covers full component access, proper chemistry, and documented results. We also publish our flat-price structure so you can verify what you’re buying. Bring us a competitor’s written estimate; we’ll put our number next to it for free.
Replace if the heat exchanger is cracked, the coil has pinhole leaks at multiple fins, or repair costs exceed 40% of replacement value. Clean if the components are structurally sound but fouled. We make this recommendation in writing, with photos, and we have no financial interest in selling you equipment we don’t carry. Our business is cleaning and repair, not replacement commissions.
Every 3-5 years for homes with standard filtration and no construction activity. Every 2-3 years if you live near active development (Stone Oak Ranch during its buildout, for example), run the fan continuously, or have pets that shed heavily. The camera inspection tells the real story - we’ve found systems that needed cleaning at 18 months and others that were fine at 6 years. We don’t sell maintenance plans; we sell honest assessments.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Round Rock at CleanRun Air Duct Cleaning Round Rock, serving Round Rock and nearby areas.